Proxmark3 community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

Announcement

Time changes and with it the technology
Proxmark3 @ discord

Users of this forum, please be aware that information stored on this site is not private.

#1 2019-03-25 13:43:34

op333
Contributor
Registered: 2019-03-25
Posts: 2

Questions about cloning Indala on T5577 with PM3 Easy

Hi all!

I hope I'm posting it the wright section.

I'm trying to clone a LF Indala card
but it isn't recognized with offline search command as valid known card.
However I get something when using the U option and it goes as follow

[-] no repeating pattern found         
PSK1 demoded bitstream:         
1011111010101111
1111111111111111
1111111110000101
1110110011001011
1011111010101111
1111111111111111
1111111110000101
1110110011001011
1011111010101111
1111111111111111
1111111110000101
1110110011001011
1011111010101111
1111111111111111
1111111110000101
1110110011001011
1011111010101111
1111111111111111
1111111110000101
1110110011001011
1011111010101111
1111111111111111
1111111110000101
1110110011001011
1011111010101111
1111111111111111
1111111110000101
1110110011001011
1011111010101111
1111111111111111
11         
Possible unknown PSK1 Modulated Tag Found above!
Could also be PSK2 - try 'data rawdemod p2'         
Could also be PSK3 - [currently not supported]         
Could also be NRZ - try 'data nrzrawdemod   


and although I can simulate the lf tag in memory or from trace file correctly onto another usb reader
I am still unable to program/clone it to a T5577 Card

Another strange thing is when I read it by using the official-64-20190324 GUI
without reflashing the PM3 Easy (icemen fork boot and image still in the PM3)
It is able to read the tag as
proxmark3> lf indala read
BitLen: 64         
Indala UID=1010000000000000
0000000000000000
1111010000100110
0110100010000010
(a0000000f4266882)

Then I use the lf t55xx write b 0 d a0000000f4266882 command
and although it seems to write on the card, when I use
lf t55xx read b 0 override_safety page1
I get nothing, card is still blank
Even wiping the T5577 doesn't show the card is blank (i think)

pm3 --> lf t55xx wipe         

Beginning Wipe of a T55xx tag (assuming the tag is not password protected)
         
Writing page 0  block: 00  data: 0x000880E0 pwd: 0x00000000         
Writing page 0  block: 01  data: 0x00000000           
Writing page 0  block: 02  data: 0x00000000           
Writing page 0  block: 03  data: 0x00000000           
Writing page 0  block: 04  data: 0x00000000           
Writing page 0  block: 05  data: 0x00000000           
Writing page 0  block: 06  data: 0x00000000           
Writing page 0  block: 07  data: 0x00000000           
pm3 --> lf t55xx dump         
Reading Page 0:         
blk | hex data | binary                           | ascii         
----+----------+----------------------------------+-------         
Reading Page 1:         
blk | hex data | binary                           | ascii         
----+----------+----------------------------------+-------         



Now, I get that there might be a lot of things I don't do properly and my learning curve is a bit
steep but I would like a bit of help...
To start with, is the problem my lack of knowledge or my cloned version PM3 Easy
Would the trace file be of any help if I post it?
Thank you

Offline

Board footer

Powered by FluxBB